Gire el estante hacia arriba y tire hacia adelante, como se muestra. Process: Install (4) Leveling Feet LL. Panel lateral B. Parte superior C. Panel posterior D. Estante E. Puerta izquierda F. Puerta derecha G. Parte inferior H. INSTALA EL FONDO Y LAS ALAS DE LAS BISAGRAS INSERTA LOS ESTANTES INTERIORES Elementos necesarios: AA - Perno con cabeza de hongo de 1,6 cm (5/8) de largo, 6,4 mm (1/4in) de dimetro y 20 roscas por pulgada (cantidad: 4) BB - Tornillo de cabeza redondeada de 19 mm (3/4in) de largo, 6,4 mm (1/4in) de dimetro y 20 roscas por pulgada (cantidad: 8) CC - Arandela de 8,7 mm (11/32in) (cantidad: 4) DD - Tuerca de la brida dentada de 6,4 mm (1/4in) de dimetro y 20 roscas por pulgada (cantidad: 12) RR - Bisagra. Finger tighten. situation which, if not avoided, will result in serious injury. MANUAL DEL OPERADOR ARMARIO PARA PISO DE 81,3 CM (32 IN) -- MODELO N. 32FC01BP-THD ARMARIO PARA PISO DE 91,4 CM (36 IN) -- MODELO N. 36FC01BP-THD ARMARIO PARA PISO DE 121,9 CM (48 IN) - MODELO N. 48FC01BP-THD MANTENIMIENTO Las superficies deben limpiarse de manera regular con agua y un detergente suave. Operating Instructions before rst use of this product. The wax will also help protect the unit against scratches. which, if not avoided, may result in minor injury. Failure to do so may cause personal injury, is used to indicate a hazardous situation, mount this product on a truck bed or any other. ATTACH TOP Items Needed: BB - 1/4-20 x 3/4in Button Head Screw (Qty: 8) DD - 1/4-20 Flange Nut (Qty: 8) B - Top (Qty: 1) INSTALL LEVELING FEET Items Needed: LL - Screw Leveler (Qty: 4) Process: Insert Top B into lower end of assembly and attach using (8) BB and (8) DD. Proceso: Coloca el Imn HH en la puerta derecha donde se indica. HERRAMIENTAS HERRAMIENTAS NECESARIAS: Llave de cubo Cubo de 9,5 mm (3/8in) Cubo profundo de 11,1 mm (7/16in) Llave espaola de 11,1 mm (7/16in) Escuadra Destornillador de punta plana Destornillador estrellaTaladro Broca para taladro de 3,2 mm (1/8in) Broca para taladro de 6,4 mm (1/4in) LL - Nivelador de tornillos (cantidad: 4) PIEZAS INCLUIDAS: AA - Perno con cabeza de hongo de 1,6 cm (5/8in) de largo, 6,4 mm (1/4in) de dimetro y 20 roscas por pulgada (cantidad: 14) MM - Tornillo de cabeza hex. Close the door to double check the Magnets are in the correct positions. Grease and oil can be removed with most standard cleaning fluids. Cierra la puerta para cerciorarte que los Imanes estn en la posicin correcta. NOTE: When placing a hinge plate (RR) on the unit the loop of the hinge MUST always face towards the outside of the unit. Failure to do so may cause personal injury or, this unit. DOOR CONSTRUCTION Items Needed: GG - #10-24 Hex Nut (Qty: 8) FF - 3/16in Washer (Qty: 8) NN - Left Hinge (Qty: 2) PP - Right Hinge (Qty: 2) EE - #10-24 Carriage Bolt (Qty: 8) E - Door Left (Qty: 1) F - Door Right (Qty: 1) DOOR HINGE ATTACHMENT Items Needed: AA - 1/4-20 x 5/8in Carriage Bolt (Qty: 4) CC - 5/16-in Washer (Qty: 4) DD - 1/4-20 Serrated Flange Nut (Qty: 4) RR - Hinge Plate (Qty: 2) Process: Slide the left door hinge pin PP into the lower hinge plate RR. Process: Note: Mounting bracket may be mounted on either side of the cabinet. Leave end holes open for later assembly. if not avoided, could result in serious injury or death. Finger tighten. Make sure the adhesive backing is facing towards the cabinet. LOCK INSTALLATION Items Needed: KK - Single Bitted Lock (Qty: 1) MAGNET INSTALLATION Items Needed: HH - Magnet (Qty: 2) Process: Assemble the Single Bitted Lock KK. Open the door and remove the protective covering over the adhesive on the back of the magnet. Some adjustments may be necessary after cabinet is in desired location. : 4) RR - Placa de la bisagra (Cant: 2) Elementos necesarios: EE - Perno con cabeza de hongo de 1,6 cm (5/8in) de largo, 6,4 mm (1/4in) de dimetro y 20 roscas por pulgada (cantidad: 4)GG - Tuerca Allen n. INSTALACIN DEL IMN INSTALACIN DE LA CERRADURA Elementos necesarios: KK - Dispositivo de seguridad con una sola broca (Cant: 1) Elementos necesarios: HH - Imn (Cant. Rotate shelf upward and pull forward, as shown. Process: Place the Magnet HH on the right door in the locations noted. FIJA EL TOPE INSTALA LA PATA NIVELADORA Elementos necesarios: BB - Tornillo de cabeza redondeada de 19 mm (3/4in) de largo, 6,4 mm (1/4in) de dimetro y 20 roscas por pulgada (cantidad: 8) DD - Tuerca de la brida dentada de 6,4 mm (1/4in) de dimetro y 20 roscas por pulgada (cantidad: 8) B - Parte superior (cantidad: 1) Elementos necesarios: LL - Nivelador de tornillos (cantidad: 4) Proceso: Instale (4) niveladores de tornillos LL. Insert back of shelf in notches, rotate shelf into place and reinstall fasteners. ATTACH BOTTOM AND HINGE PLATES Items Needed: AA - 1/4-20 x 5/8in Carriage Bolt (Qty: 4) BB - 1/4-20 x 3/4in Button Head Screw (Qty: 8) CC - 5/16in Washer (Qty: 4) DD - 1/4-20 Flange Nut (Qty: 12) RR - Hinge Plate (Qty: 2) G - Bottom (Qty: 1) Process: Insert Bottom G into one end of assembly (either end will work) and attach using (8) BB, and (8) DD. OPERATORS MANUAL 32 IN FLOOR CABINET -- MODEL # 32FC01BP-THD 36-IN FLOOR CABINET -- 36FC01BP-THD 48 IN FLOOR CABINET -- MODEL # 48FC01BP-THD MAINTENANCE Periodically the surfaces should be cleaned with a mild detergent and water. ADITAMENTO DE LA BISAGRA DE LA PUERTA MONTAJE DE LA PUERTA Elementos necesarios: AA - 1/4-20 x 5/8in Pernos de Carro (Cant: 4) CC - 5/16-in Arandela (Cant: 4) DD - Tuerca de Reborde Dentado de 0,63 cm 50,8 cm (Cant. For safety, use a nonflammable cleaning fluid. Finger tighten. Quite los sujetadores. This may cause personal injury or product, hand tools. Empty weight of the 48-in unit is 148 lbs. HARDWARE TOOLS REQUIRED: Socket Wrench 7/16in Deep-well Socket Square Cross-tip Screwdriver 1/8in Drill Bit 3/8in Socket 7/16in Open End Wrench Flathead Screwdriver Drill 1/4in Drill Bit LL - Screw Leveler (Qty: 4) HARDWARE INCLUDED: AA - 1/4-20 X 5/8in Carriage Bolt (Qty: 14) MM - #14 x 3 Hex Head Screw (Qty: 1) BB - 1/4-20 X 3/4in Button Head Screw (Qty: 24) NN - Left Hinge (Qty: 2) CC - 5/16in Washer (Qty: 14) DD - 1/4-20 Flange Nut (Qty: 38) PP - Right Hinge (Qty: 2) EE - #10-24 x 1/2in C. CARTON CONTENTS A. Remove fasteners. CONTENIDO DE LA CAJA A. Failure to do so may cause personal injury or, become unstable and tip if stored or moved on an un-level, surface, which may cause personal injury or product, Failure to do so may cause personal injury or product, Concrete or other surfaces will require other hardware, (not provided). Comprueba que la superficie adhesiva mire hacia el gabinete. OPERATION FINAL PLACEMENT Items Needed: BB - 1/4-20 x 3/4in Button Head Screw (Qty: 1) DD - 1/4-20 Flange Nut (Qty: 1) H - Mounting Bracket (Qty: 1) MM - #14 x 3 Hex Head Screw (Qty: 1) SHELF ADJUSTMENT Empty shelf. Use appropriate hardware per your local, building codes. Apply the wax as to a car. Para su seguridad, utilice un lquido de limpieza no inflamable. for the 48-in unit, The maximum product weight including contents stored on the, shelves is 934 lbs for the 32-in unit, 766 lbs for the 36-in unit, Model numbers and other information required for service parts is. COLOCACIN FINAL FUNCIONAMIENTO Elementos necesarios: BB - Tornillo de cabeza redondeada de 19 mm (3/4in) de largo, 6,4 mm (1/4in) de dimetro y 20 roscas por pulgada (cantidad: 1) DD - Tuerca de la brida dentada de 6,4 mm (1/4in) de dimetro y H - 20 roscas por pulgada (cantidad: 1) MM - Soporte de montaje (cantidad: 1) Ajuste del estante Vace el estante. Empty weight of the 36-in unit is 141 lbs. Move shelf to desired location. for the 32-, in unit, 125 lbs for the 36-in unit and 100 lbs. Empty weight of the 32-in unit is 109 lbs. Las manchas de grasa y aceite pueden quitarse con la mayora de los lquidos de limpieza estndar. B. C. D. Side Panel Top Back Panel Shelf E. F. G. H. Door Left Door Right Bottom Wall Bracket ATTACH SIDE PANELS Items Needed: BB - 1/4-20 x 3/4in Button Head Screw (Qty: 4) DD - 1/4-20 Serrated Flange Nut (Qty: 4) A - Side Panel (Qty: 2) Process: Attach (2) Sides A using (2) BB, and (2) DD in middle holes of each side. : 2) Proceso: Arme el dispositivo de seguridad con una sola broca KK. Auto wax will preserve the units luster finish. located on a white label on the upper right hand corner of the unit. moving object. The maximum load capacity for each shelf is 165 lbs.
Skechers Velcro Shoes, Sleeping Positions To Avoid After C-section, Sutera Dream Deep Pillow, Super Lightweight Flatbed Tarps, Democracy Karessa Capri Skinny Jean, Dish Drying Mat Dollar Tree, Tight Long Sleeve Dress, Sam Edelman Silver Felicia Flats, Barbie Shopping Time Doll, Helly Hansen W Crew Fleece Jacket,
